Dangel · Jumper · Recommended
Dangel Jumper recommended cold inflation
- Drivetrain
- front-wheel drive
- Body
- light commercial
- PSI F / R
- 35-45 / 45-65
- Bar F / R
- 2.4-3.1 / 3.1-4.5
psi
40 / 55
Catalogue mid-points, front / rear · 2.4-3.1 / 3.1-4.5 bar
35-45 psi F · 45-65 psi R · 2.4-3.1 / 3.1-4.5 bar · 276/379 kPa
Recommended pressure means the vehicle placard, not the tyre sidewall. For a Dangel Jumper the catalogue proxy is 35-45/45-65 psi (2.4-3.1/3.1-4.5 bar). TPMS typically warns near 30 psi (about 25% below target). That is already a soft tyre, not a fill target.
How to set the Jumper
- Park the Dangel Jumper for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 35-45 psi / 2.4-3.1 bar front and 45-65 psi / 3.1-4.5 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Jumper is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Dangel Jumper placard versus sidewall
The tyre-information placard on a Dangel Jumper sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 35-45 / 45-65 psi.
Estimated pressure by tyre size (285/70R17 and others)
Planning cold pressures for sizes often seen on a light commercial. This Jumper sample opens with 285/70R17, then 245/70R16 and LT245/75R16.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 285/70R17 | 44 | 62 | 3.03 | 4.27 | 303 | 427 | Wide all-terrain |
| 245/70R16 | 42 | 59 | 2.9 | 4.07 | 290 | 407 | Common 16-inch all-terrain |
| LT245/75R16 | 48 | 67 | 3.31 | 4.62 | 331 | 462 | LT-metric, higher load |
| 235/75R15 | 41 | 58 | 2.83 | 4 | 283 | 400 | Older compact truck |
| 255/65R17 | 43 | 60 | 2.96 | 4.14 | 296 | 414 | Highway 17-inch |
| LT265/70R17 | 48 | 69 | 3.31 | 4.76 | 331 | 476 | LT 17-inch |
| 275/65R18 | 43 | 61 | 2.96 | 4.21 | 296 | 421 | Plus-size 18-inch |
| 265/70R17 | 43 | 60 | 2.96 | 4.14 | 296 | 414 | Typical 17-inch load tyre |
PSI, bar and kPa
PSI-led conversions for the Dangel Jumper band (35-45 / 45-65).
| PSI | Bar | kPa |
|---|---|---|
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 45 | 3.10 | 310 |
| 50 | 3.45 | 345 |
| 55 | 3.79 | 379 |
| 60 | 4.14 | 414 |
| 65 | 4.48 | 448 |
Pressure against load
Load moves the rear of a light commercial first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 40 psi / 2.76 bar | 55 psi / 3.79 bar |
| Full occupancy | 41 psi / 2.83 bar | 57 psi / 3.93 bar |
| Motorway + luggage | 42 psi / 2.9 bar | 57 psi / 3.93 bar |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 40 psi as a 20 °C baseline for this Jumper.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 37 psi | 2.55 bar | 255 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 38 psi | 2.62 bar | 262 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 39 psi | 2.69 bar | 269 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 40 psi | 2.76 bar | 276 kPa | Baseline |
| 30 °C | 42 psi | 2.9 bar | 290 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 43 psi | 2.96 bar | 296 kPa | Do not bleed a hot tyre |
Dangel notes
No special Dangel exception: the Jumper uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Dangel Jumper usually follows the higher axle (often the rear, near 45-65 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Dangel sticker and this page disagree, the sticker wins.
Other Dangel models
Questions about this Jumper
What is that in bar and kPa for the Jumper?
Mid-points are about 2.76 bar (276 kPa) front and 3.79 bar (379 kPa) rear.
What tyre pressure should a Dangel Jumper use?
Catalogue reference is 35-45 psi front and 45-65 psi rear (2.4-3.1 / 3.1-4.5 bar), cold. Confirm on the door-pillar placard.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
Is the sidewall number correct on a Dangel Jumper?
No. Sidewall PSI is a maximum. The Jumper placard is the operating target, near 35-45/45-65 psi.
What PSI if I plus-size toward LT245/75R16?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 285/70R17, 245/70R16 and LT245/75R16 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation