UK · EU reference Tyre Pressure

Suzuki · LJ 80 · Front

Suzuki LJ 80 front tyre pressure

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

psi front

34

2.31 bar · 231 kPa at the steering axle

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

A 3 psi miss on one front corner of this LJ 80 shows up as a wander before the TPMS lamp bothers you. Target 34 psi (2.31 bar) cold. Under-inflation cooks the shoulders of a LJ 80; over-inflation wears the centre rib and bangs every cat’s eye.

Suzuki LJ 80 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this LJ 80 is the pillar sticker, near 34/34 psi.

Estimated pressure by tyre size (225/40R18 and others)

Planning cold pressures for sizes often seen on a passenger car. This LJ 80 sample opens with 225/40R18, then 195/65R15 and 215/55R16.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
225/40R18362.48248Low-profile 18-inch
195/65R15342.34234Very common compact
215/55R16342.34234Slightly wider 16-inch
215/50R17352.41241Plus-size 17-inch
205/60R16342.34234Taller 16-inch
245/40R18362.48248Wide touring 18-inch
225/50R17352.41241Touring 17-inch
225/45R17352.41241Sport 17-inch

Pressure against load

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy34 psi / 2.34 bar35 psi / 2.41 bar
Motorway + luggage35 psi / 2.41 bar36 psi / 2.48 bar

Steering feel on the LJ 80 lives on this axle. Do not drop front pressure to “soften” a plus-size 215/55R16; you will roll the sidewall in a roundabout.

How to set the LJ 80

  1. Measure before the school run, not after the M25.
  2. Write LF / RF / RR / RL. Do not keep LJ 80 numbers in your head.
  3. Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
  4. If one corner is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

PSI, bar and kPa

PSI-led conversions for the Suzuki LJ 80 band (32-35 / 32-35).

PSIBarkPa
302.07207
322.21221
332.28228
33.52.31231
352.41241
362.48248
382.62262
402.76276
443.03303
503.45345
604.14414

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this LJ 80.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

Suzuki notes

No special Suzuki exception: the LJ 80 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Suzuki LJ 80 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Suzuki sticker and this page disagree, the sticker wins.

Other Suzuki models

Questions about this LJ 80

What is that in bar and kPa for the LJ 80?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

How often should I check a LJ 80?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

When does TPMS warn on a Suzuki LJ 80?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Is the sidewall number correct on a Suzuki LJ 80?

No. Sidewall PSI is a maximum. The LJ 80 placard is the operating target, near 32-35/32-35 psi.

What tyre pressure should a Suzuki LJ 80 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation