Subaru · M80 · Overview
Subaru M80 tyre pressure
- Drivetrain
- all-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
This all-wheel drive passenger car is filed here with a working range of 32-35/32-35 psi. The pillar sticker on your VIN still overrides the website. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target. Keep side-to-side spread inside about 2 psi so the all-wheel drive hardware is not working on a radius mismatch.
PSI, bar and kPa
1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Mid-points on the M80: 34 psi = 2.31 bar = 231 kPa.
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Spare and inflator kit
A matching full-size spare on the Subaru M80 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 38 psi / 2.62 bar |
How to set the M80
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep M80 numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Subaru notes
No special Subaru exception: the M80 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Temperature and a cold gauge
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this M80.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Estimated pressure by tyre size (225/40R18 and others)
Planning cold pressures for sizes often seen on a passenger car. This M80 sample opens with 225/40R18, then 275/35R18 and 235/35R19.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/40R18 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Front 18-inch |
| 275/35R18 | 36 | 37 | 2.48 | 2.55 | 248 | 255 | Wide rear |
| 235/35R19 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Front 19-inch |
| 255/35R18 | 35 | 36 | 2.41 | 2.48 | 241 | 248 | Rear stagger 18-inch |
| 275/30R19 | 36 | 37 | 2.48 | 2.55 | 248 | 255 | Rear 19-inch |
| 255/40R17 | 35 | 36 | 2.41 | 2.48 | 241 | 248 | Rear stagger 17-inch |
| 245/40R18 | 35 | 36 | 2.41 | 2.48 | 241 | 248 | Square-ish sport |
| 225/45R17 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Front sport size |
Subaru M80 placard versus sidewall
If the Subaru sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
If the Subaru sticker and this page disagree, the sticker wins.
Other Subaru models
Questions about this M80
What is that in bar and kPa for the M80?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Is the sidewall number correct on a Subaru M80?
No. Sidewall PSI is a maximum. The M80 placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 235/35R19?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/40R18, 275/35R18 and 235/35R19 as a planning band.
What tyre pressure should a Subaru M80 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Front versus rear on the Subaru M80?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
Handbook: placard · bar vs PSI · front vs rear · cold inflation