StreetScooter · Work · Front

Front axle PSI and bar on the StreetScooter Work

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi front

2.31 bar · 231 kPa at the steering axle

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

The front axle of a StreetScooter Work steers and, on front-wheel drive cars, often pulls as well. Catalogue front pressure is 32-35 psi / 2.2-2.4 bar. Size estimates on this page include 215/50R17, 205/55R16 and 215/55R16 — interpolated from the catalogue midpoint, not a second factory sticker.

StreetScooter Work placard versus sidewall

The tyre-information placard on a StreetScooter Work sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (215/50R17 and others)

215/50R17 is the first planning size here. 215/55R16 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
215/50R17	35	—	2.41	—	241	—	Plus-size 17-inch
205/55R16	34	—	2.34	—	234	—	Typical mid-compact OEM
215/55R16	34	—	2.34	—	234	—	Slightly wider 16-inch
205/60R16	34	—	2.34	—	234	—	Taller 16-inch
245/40R18	36	—	2.48	—	248	—	Wide touring 18-inch
225/45R17	35	—	2.41	—	241	—	Sport 17-inch
225/50R17	35	—	2.41	—	241	—	Touring 17-inch
195/65R15	34	—	2.34	—	234	—	Very common compact

Pressure against load

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	36 psi / 2.48 bar

Steering feel on the Work lives on this axle. Do not drop front pressure to “soften” a plus-size 215/55R16; you will roll the sidewall in a roundabout.

How to set the Work

Park the StreetScooter Work for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Work is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

PSI, bar and kPa

PSI-led conversions for the StreetScooter Work band (32-35 / 32-35).

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Work.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

StreetScooter notes

No special StreetScooter exception: the Work uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the StreetScooter Work usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the StreetScooter sticker and this page disagree, the sticker wins.

Other StreetScooter models

Work L

Questions about this Work

What is that in bar and kPa for the Work?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

What tyre pressure should a StreetScooter Work use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

How often should I check a Work?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Is the sidewall number correct on a StreetScooter Work?

No. Sidewall PSI is a maximum. The Work placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation