StreetScooter · Work · Bar

Recommended bar for a StreetScooter Work

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Work 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Size estimates on this page include 225/50R17, 195/65R15 and 205/60R16 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the StreetScooter Work. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

StreetScooter Work placard versus sidewall

The tyre-information placard on a StreetScooter Work sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (225/50R17 and others)

If your StreetScooter Work no longer wears the OEM diameter, start at the row nearest 225/50R17 or 195/65R15 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	38 psi / 2.62 bar

How to set the Work

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep Work numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Work.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

StreetScooter notes

No special StreetScooter exception: the Work uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the StreetScooter Work usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the StreetScooter sticker and this page disagree, the sticker wins.

Other StreetScooter models

Work L

Questions about this Work

What is that in bar and kPa for the Work?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

When does TPMS warn on a StreetScooter Work?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Front versus rear on the StreetScooter Work?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

How often should I check a Work?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

What tyre pressure should a StreetScooter Work use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation