Mitsubishi · Pajero Pinin · Bar

Mitsubishi Pajero Pinin tyre pressure in bar

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

European and UK handbooks usually quote bar. The Mitsubishi Pajero Pinin catalogue is 2.2-2.4 bar front and 2.2-2.4 bar rear (midpoint 2.31 / 2.31). Size estimates on this page include 225/45R17, 225/40R18 and 245/40R18 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the Mitsubishi Pajero Pinin. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Mitsubishi Pajero Pinin placard versus sidewall

If the Mitsubishi sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (225/45R17 and others)

If your Mitsubishi Pajero Pinin no longer wears the OEM diameter, start at the row nearest 225/45R17 or 225/40R18 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	38 psi / 2.62 bar

How to set the Pajero Pinin

Park the Mitsubishi Pajero Pinin for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Pajero Pinin is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Pajero Pinin.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Mitsubishi notes

No special Mitsubishi exception: the Pajero Pinin uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Mitsubishi Pajero Pinin usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

A cheap gauge and a monthly habit will do more for this Pajero Pinin than nitrogen upsells.

Other Mitsubishi models

Cosmos Colt L200 Diamante Dion Carisma Grandis Galant

Questions about this Pajero Pinin

What is that in bar and kPa for the Pajero Pinin?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

When does TPMS warn on a Mitsubishi Pajero Pinin?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Is the sidewall number correct on a Mitsubishi Pajero Pinin?

No. Sidewall PSI is a maximum. The Pajero Pinin placard is the operating target, near 32-35/32-35 psi.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a Mitsubishi Pajero Pinin use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation