Mitsubishi · Pajero Pinin · Cold
Setting cold tyres on a Mitsubishi Pajero Pinin
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Cold means the Mitsubishi Pajero Pinin has stood at least three hours, or covered less than about a mile. Heat from a dual carriageway run is not the number you set. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Temperature and a cold gauge
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Pajero Pinin.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the Pajero Pinin
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep Pajero Pinin numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Mitsubishi Pajero Pinin placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Pajero Pinin is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (245/40R18 and others)
If your Mitsubishi Pajero Pinin no longer wears the OEM diameter, start at the row nearest 245/40R18 or 185/65R15 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
PSI, bar and kPa
PSI-led conversions for the Mitsubishi Pajero Pinin band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
Mitsubishi notes
No special Mitsubishi exception: the Pajero Pinin uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Mitsubishi Pajero Pinin usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Mitsubishi sticker and this page disagree, the sticker wins.
Other Mitsubishi models
Questions about this Pajero Pinin
What is that in bar and kPa for the Pajero Pinin?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Is the sidewall number correct on a Mitsubishi Pajero Pinin?
No. Sidewall PSI is a maximum. The Pajero Pinin placard is the operating target, near 32-35/32-35 psi.
How often should I check a Pajero Pinin?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
When does TPMS warn on a Mitsubishi Pajero Pinin?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
What tyre pressure should a Mitsubishi Pajero Pinin use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation