Mitsubishi · Dion · Bar

Mitsubishi Dion bar chart (2.2-2.4 / 2.2-2.4)

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Dion 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Under-inflation cooks the shoulders of a Dion; over-inflation wears the centre rib and bangs every cat’s eye.

Bar, PSI and kPa

Bar-led conversions around the Mitsubishi Dion. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Mitsubishi Dion placard versus sidewall

If the Mitsubishi sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (205/55R16 and others)

205/55R16 is the first planning size here. 225/50R17 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	38 psi / 2.62 bar

How to set the Dion

Park the Mitsubishi Dion for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Dion is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Dion.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Mitsubishi notes

No special Mitsubishi exception: the Dion uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Mitsubishi Dion usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Mitsubishi sticker and this page disagree, the sticker wins.

Other Mitsubishi models

DINGO L300 L400 Grandis Diamante Canter Airtrek FTO

Questions about this Dion

What tyre pressure should a Mitsubishi Dion use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

How often should I check a Dion?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What is that in bar and kPa for the Dion?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

What PSI if I plus-size toward 225/50R17?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 205/55R16, 215/55R16 and 225/50R17 as a planning band.

Handbook: placard · bar vs PSI · front vs rear · cold inflation