Mitsubishi · 400 · Rear
Mitsubishi 400 rear tyre pressure
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi rear
34
2.31 bar · 231 kPa at the rear axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
The rear of a passenger car takes passengers, luggage and, on vans, payload. Catalogue rear pressure on the Mitsubishi 400 is 32-35 psi / 2.2-2.4 bar. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Mitsubishi 400 placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this 400 is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (245/40R18 and others)
If your Mitsubishi 400 no longer wears the OEM diameter, start at the row nearest 245/40R18 or 185/65R15 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 245/40R18 | — | 36 | — | 2.48 | — | 248 | Wide touring 18-inch |
| 185/65R15 | — | 33 | — | 2.28 | — | 228 | Small / older car |
| 225/50R17 | — | 35 | — | 2.41 | — | 241 | Touring 17-inch |
| 205/60R16 | — | 34 | — | 2.34 | — | 234 | Taller 16-inch |
| 195/65R15 | — | 34 | — | 2.34 | — | 234 | Very common compact |
| 215/55R16 | — | 35 | — | 2.41 | — | 241 | Slightly wider 16-inch |
| 225/45R17 | — | 35 | — | 2.41 | — | 241 | Sport 17-inch |
| 205/55R16 | — | 34 | — | 2.34 | — | 234 | Typical mid-compact OEM |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
A family passenger car with a boot full of luggage should use the laden rear figure if Ford, VW or Mercedes printed one. Otherwise the modest steps in the load table are only a sketch for this 400.
How to set the 400
- Park the Mitsubishi 400 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive 400 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Mitsubishi 400 band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 400.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Mitsubishi notes
No special Mitsubishi exception: the 400 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Mitsubishi 400 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Mitsubishi sticker and this page disagree, the sticker wins.
Other Mitsubishi models
Questions about this 400
Front versus rear on the Mitsubishi 400?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
Is the sidewall number correct on a Mitsubishi 400?
No. Sidewall PSI is a maximum. The 400 placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 225/50R17?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 245/40R18, 185/65R15 and 225/50R17 as a planning band.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What is that in bar and kPa for the 400?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Handbook: placard · bar vs PSI · front vs rear · cold inflation