Bertone · Cabrio · Overview

Tyre pressure chart for the Bertone Cabrio

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

The Bertone Cabrio catalogue band is 32-35 psi front and 32-35 psi rear — 2.2-2.4 / 2.2-2.4 bar, or about 231 / 231 kPa — measured cold. Size estimates on this page include 215/55R16, 225/45R17 and 195/65R15 — interpolated from the catalogue midpoint, not a second factory sticker.

Pressure against load

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	37 psi / 2.55 bar

PSI, bar and kPa

1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Mid-points on the Cabrio: 34 psi = 2.31 bar = 231 kPa.

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

How to set the Cabrio

Park the Bertone Cabrio for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Cabrio is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Bertone Cabrio placard versus sidewall

If the Bertone sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Bertone notes

No special Bertone exception: the Cabrio uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Bertone Cabrio usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

Estimated pressure by tyre size (215/55R16 and others)

215/55R16 is the first planning size here. 195/65R15 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch

Temperature and a cold gauge

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Cabrio.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Keep the Bertone Cabrio on the printed band; use 215/55R16 and 195/65R15 only as a map for non-OEM wheels.

Other Bertone models

Questions about this Cabrio

What tyre pressure should a Bertone Cabrio use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Front versus rear on the Bertone Cabrio?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

When does TPMS warn on a Bertone Cabrio?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

How often should I check a Cabrio?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Is the sidewall number correct on a Bertone Cabrio?

No. Sidewall PSI is a maximum. The Cabrio placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation