Bertone · Cabrio · Front
Bertone Cabrio front tyres: 32-35 psi / 2.2-2.4 bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
The front axle of a Bertone Cabrio steers and, on front-wheel drive cars, often pulls as well. Catalogue front pressure is 32-35 psi / 2.2-2.4 bar. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Bertone Cabrio placard versus sidewall
If the Bertone sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Estimated pressure by tyre size (205/60R16 and others)
Planning cold pressures for sizes often seen on a passenger car. This Cabrio sample opens with 205/60R16, then 215/55R16 and 245/40R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 205/60R16 | 34 | — | 2.34 | — | 234 | — | Taller 16-inch |
| 215/55R16 | 34 | — | 2.34 | — | 234 | — | Slightly wider 16-inch |
| 245/40R18 | 36 | — | 2.48 | — | 248 | — | Wide touring 18-inch |
| 215/50R17 | 35 | — | 2.41 | — | 241 | — | Plus-size 17-inch |
| 205/55R16 | 34 | — | 2.34 | — | 234 | — | Typical mid-compact OEM |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
| 225/40R18 | 36 | — | 2.48 | — | 248 | — | Low-profile 18-inch |
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
Steering feel on the Cabrio lives on this axle. Do not drop front pressure to “soften” a plus-size 245/40R18; you will roll the sidewall in a roundabout.
How to set the Cabrio
- Park the Bertone Cabrio for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Cabrio is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Bertone Cabrio band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Cabrio.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Bertone notes
No special Bertone exception: the Cabrio uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Bertone Cabrio usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Bertone sticker and this page disagree, the sticker wins.
Other Bertone models
Questions about this Cabrio
Front versus rear on the Bertone Cabrio?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a Bertone Cabrio use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
When does TPMS warn on a Bertone Cabrio?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
Is the sidewall number correct on a Bertone Cabrio?
No. Sidewall PSI is a maximum. The Cabrio placard is the operating target, near 32-35/32-35 psi.
Handbook: placard · bar vs PSI · front vs rear · cold inflation