BAIC · Senova X65 · Overview
BAIC Senova X65 tyre pressure
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
This front-wheel drive passenger car is filed here with a working range of 32-35/32-35 psi. The pillar sticker on your VIN still overrides the website. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Estimated pressure by tyre size (225/45R17 and others)
If your BAIC Senova X65 no longer wears the OEM diameter, start at the row nearest 225/45R17 or 245/40R18 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
Spare and inflator kit
A matching full-size spare on the BAIC Senova X65 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
BAIC notes
No special BAIC exception: the Senova X65 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
BAIC Senova X65 placard versus sidewall
If the BAIC sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
PSI, bar and kPa
1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Mid-points on the Senova X65: 34 psi = 2.31 bar = 231 kPa.
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 37 psi / 2.55 bar |
Temperature and a cold gauge
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Senova X65.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the Senova X65
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep Senova X65 numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
If the BAIC sticker and this page disagree, the sticker wins.
Other BAIC models
Questions about this Senova X65
Is the sidewall number correct on a BAIC Senova X65?
No. Sidewall PSI is a maximum. The Senova X65 placard is the operating target, near 32-35/32-35 psi.
Front versus rear on the BAIC Senova X65?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a BAIC Senova X65 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
When does TPMS warn on a BAIC Senova X65?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
How often should I check a Senova X65?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Handbook: placard · bar vs PSI · front vs rear · cold inflation