BAIC · Senova X65 · Cold

Cold tyre pressure for a BAIC Senova X65

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

Cold means the BAIC Senova X65 has stood at least three hours, or covered less than about a mile. Heat from a dual carriageway run is not the number you set. Size estimates on this page include 205/55R16, 195/65R15 and 225/40R18 — interpolated from the catalogue midpoint, not a second factory sticker.

Temperature and a cold gauge

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Senova X65.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

How to set the Senova X65

Park the BAIC Senova X65 for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Senova X65 is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

BAIC Senova X65 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this Senova X65 is the pillar sticker, near 34/34 psi.

Estimated pressure by tyre size (205/55R16 and others)

If your BAIC Senova X65 no longer wears the OEM diameter, start at the row nearest 205/55R16 or 195/65R15 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
195/65R15	34	34	2.34	2.34	234	234	Very common compact
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch

PSI, bar and kPa

PSI-led conversions for the BAIC Senova X65 band (32-35 / 32-35).

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	38 psi / 2.62 bar

BAIC notes

No special BAIC exception: the Senova X65 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the BAIC Senova X65 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the BAIC sticker and this page disagree, the sticker wins.

Other BAIC models

D20 Senova X55 B40 Senova D50 Beijing X75 Beijing X55 BJ60 Senova X25

Questions about this Senova X65

Front versus rear on the BAIC Senova X65?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Is the sidewall number correct on a BAIC Senova X65?

No. Sidewall PSI is a maximum. The Senova X65 placard is the operating target, near 32-35/32-35 psi.

What tyre pressure should a BAIC Senova X65 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

What PSI if I plus-size toward 225/40R18?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 205/55R16, 195/65R15 and 225/40R18 as a planning band.

Handbook: placard · bar vs PSI · front vs rear · cold inflation