Segway · Villain SX10 · PSI

What PSI for a Segway Villain SX10?

Drivetrain: front-wheel drive
Body: SUV / crossover
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

A Segway Villain SX10 run at sidewall-max (often 44–51 psi) is over-inflated for this SUV / crossover. The operating PSI is 32-35/32-35. Size estimates on this page include 225/65R17, 245/55R19 and 235/65R17 — interpolated from the catalogue midpoint, not a second factory sticker.

Segway Villain SX10 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this Villain SX10 is the pillar sticker, near 34/34 psi.

PSI, bar and kPa

PSI-led conversions for the Segway Villain SX10 band (32-35 / 32-35).

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

Estimated pressure by tyre size (225/65R17 and others)

If your Segway Villain SX10 no longer wears the OEM diameter, start at the row nearest 225/65R17 or 245/55R19 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/65R17	35	35	2.41	2.41	241	241	Very common 17-inch
245/55R19	36	36	2.48	2.48	248	248	Low-profile 19-inch
235/65R17	35	36	2.41	2.48	241	248	Mid-size SUV
245/60R18	36	37	2.48	2.55	248	255	Heavier CUV
215/70R16	34	34	2.34	2.34	234	234	Compact crossover
235/60R18	36	36	2.48	2.48	248	248	Plus-size 18-inch
255/50R20	37	37	2.55	2.55	255	255	20-inch plus-size
225/60R18	35	35	2.41	2.41	241	241	Highway CUV

How to set the Villain SX10

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep Villain SX10 numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Load notes

Load moves the rear of a SUV / crossover first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	38 psi / 2.62 bar

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Villain SX10.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Segway notes

No special Segway exception: the Villain SX10 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Segway Villain SX10 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

Keep the Segway Villain SX10 on the printed band; use 225/65R17 and 235/65R17 only as a map for non-OEM wheels.

Other Segway models

Villain SX10 H Fugleman 1000 Villain 1000 SH Fugleman 570 Fugleman UT 10 Fugleman UT6 H

Questions about this Villain SX10

What is that in bar and kPa for the Villain SX10?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

What PSI if I plus-size toward 235/65R17?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/65R17, 245/55R19 and 235/65R17 as a planning band.

Is the sidewall number correct on a Segway Villain SX10?

No. Sidewall PSI is a maximum. The Villain SX10 placard is the operating target, near 32-35/32-35 psi.

What tyre pressure should a Segway Villain SX10 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Front versus rear on the Segway Villain SX10?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Handbook: placard · bar vs PSI · front vs rear · cold inflation