Segway · Villain SX10 · Overview

Segway Villain SX10: 2.2-2.4 bar / 32-35 psi

Drivetrain: front-wheel drive
Body: SUV / crossover
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

On a Segway Villain SX10 the useful pair is 34 psi (2.31 bar) up front and 34 psi (2.31 bar) at the back, mid-range. Size estimates on this page include 255/50R20, 235/65R17 and 245/55R19 — interpolated from the catalogue midpoint, not a second factory sticker.

Spare and inflator kit

A matching full-size spare on the Segway Villain SX10 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

Estimated pressure by tyre size (255/50R20 and others)

If your Segway Villain SX10 no longer wears the OEM diameter, start at the row nearest 255/50R20 or 235/65R17 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
255/50R20	37	37	2.55	2.55	255	255	20-inch plus-size
235/65R17	35	36	2.41	2.48	241	248	Mid-size SUV
245/55R19	36	36	2.48	2.48	248	248	Low-profile 19-inch
225/65R17	35	35	2.41	2.41	241	241	Very common 17-inch
225/60R18	35	35	2.41	2.41	241	241	Highway CUV
215/70R16	34	34	2.34	2.34	234	234	Compact crossover
245/60R18	36	37	2.48	2.55	248	255	Heavier CUV
235/60R18	36	36	2.48	2.48	248	248	Plus-size 18-inch

PSI, bar and kPa

1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Mid-points on the Villain SX10: 34 psi = 2.31 bar = 231 kPa.

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

How to set the Villain SX10

Park the Segway Villain SX10 for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Villain SX10 is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature and a cold gauge

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Villain SX10.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Segway notes

No special Segway exception: the Villain SX10 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Segway Villain SX10 placard versus sidewall

The tyre-information placard on a Segway Villain SX10 sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Pressure against load

Load moves the rear of a SUV / crossover first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	37 psi / 2.55 bar

A cheap gauge and a monthly habit will do more for this Villain SX10 than nitrogen upsells.

Other Segway models

Villain SX10 H Fugleman 1000 Villain 1000 SH Fugleman 570 Fugleman UT 10 Fugleman UT6 H

Questions about this Villain SX10

Front versus rear on the Segway Villain SX10?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

When does TPMS warn on a Segway Villain SX10?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What is that in bar and kPa for the Villain SX10?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

Is the sidewall number correct on a Segway Villain SX10?

No. Sidewall PSI is a maximum. The Villain SX10 placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation