Puch · Pinzgauer · Front
Puch Pinzgauer front tyre pressure
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A 3 psi miss on one front corner of this Pinzgauer shows up as a wander before the TPMS lamp bothers you. Target 34 psi (2.31 bar) cold. Under-inflation cooks the shoulders of a Pinzgauer; over-inflation wears the centre rib and bangs every cat’s eye.
Puch Pinzgauer placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Pinzgauer is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (225/50R17 and others)
If your Puch Pinzgauer no longer wears the OEM diameter, start at the row nearest 225/50R17 or 185/65R15 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
| 185/65R15 | 33 | — | 2.28 | — | 228 | — | Small / older car |
| 215/55R16 | 34 | — | 2.34 | — | 234 | — | Slightly wider 16-inch |
| 205/55R16 | 34 | — | 2.34 | — | 234 | — | Typical mid-compact OEM |
| 215/50R17 | 35 | — | 2.41 | — | 241 | — | Plus-size 17-inch |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
| 245/40R18 | 36 | — | 2.48 | — | 248 | — | Wide touring 18-inch |
| 225/40R18 | 36 | — | 2.48 | — | 248 | — | Low-profile 18-inch |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
Steering feel on the Pinzgauer lives on this axle. Do not drop front pressure to “soften” a plus-size 215/55R16; you will roll the sidewall in a roundabout.
How to set the Pinzgauer
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep Pinzgauer numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
PSI, bar and kPa
PSI-led conversions for the Puch Pinzgauer band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Pinzgauer.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Puch notes
No special Puch exception: the Pinzgauer uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Puch Pinzgauer usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Puch sticker and this page disagree, the sticker wins.
Other Puch models
Questions about this Pinzgauer
What is that in bar and kPa for the Pinzgauer?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What PSI if I plus-size toward 215/55R16?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/50R17, 185/65R15 and 215/55R16 as a planning band.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What tyre pressure should a Puch Pinzgauer use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Is the sidewall number correct on a Puch Pinzgauer?
No. Sidewall PSI is a maximum. The Pinzgauer placard is the operating target, near 32-35/32-35 psi.
Handbook: placard · bar vs PSI · front vs rear · cold inflation