Oldtimer · Morris Leon Bolle · Front
Oldtimer Morris Leon Bolle front tyres: 32-35 psi / 2.2-2.4 bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A 3 psi miss on one front corner of this Morris Leon Bolle shows up as a wander before the TPMS lamp bothers you. Target 34 psi (2.31 bar) cold. Under-inflation cooks the shoulders of a Morris Leon Bolle; over-inflation wears the centre rib and bangs every cat’s eye.
Oldtimer Morris Leon Bolle placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Morris Leon Bolle is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (225/45R17 and others)
Planning cold pressures for sizes often seen on a passenger car. This Morris Leon Bolle sample opens with 225/45R17, then 205/60R16 and 225/40R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/45R17 | 35 | — | 2.41 | — | 241 | — | Sport 17-inch |
| 205/60R16 | 34 | — | 2.34 | — | 234 | — | Taller 16-inch |
| 225/40R18 | 36 | — | 2.48 | — | 248 | — | Low-profile 18-inch |
| 245/40R18 | 36 | — | 2.48 | — | 248 | — | Wide touring 18-inch |
| 185/65R15 | 33 | — | 2.28 | — | 228 | — | Small / older car |
| 205/55R16 | 34 | — | 2.34 | — | 234 | — | Typical mid-compact OEM |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
Steering feel on the Morris Leon Bolle lives on this axle. Do not drop front pressure to “soften” a plus-size 225/40R18; you will roll the sidewall in a roundabout.
How to set the Morris Leon Bolle
- Park the Oldtimer Morris Leon Bolle for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Morris Leon Bolle is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Oldtimer Morris Leon Bolle band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Morris Leon Bolle.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Oldtimer notes
No special Oldtimer exception: the Morris Leon Bolle uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Oldtimer Morris Leon Bolle usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
Keep the Oldtimer Morris Leon Bolle on the printed band; use 225/45R17 and 225/40R18 only as a map for non-OEM wheels.
Other Oldtimer models
Questions about this Morris Leon Bolle
What PSI if I plus-size toward 225/40R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 205/60R16 and 225/40R18 as a planning band.
What tyre pressure should a Oldtimer Morris Leon Bolle use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Is the sidewall number correct on a Oldtimer Morris Leon Bolle?
No. Sidewall PSI is a maximum. The Morris Leon Bolle placard is the operating target, near 32-35/32-35 psi.
What is that in bar and kPa for the Morris Leon Bolle?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
When does TPMS warn on a Oldtimer Morris Leon Bolle?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
Handbook: placard · bar vs PSI · front vs rear · cold inflation