Oldtimer · Humber · Bar

Oldtimer Humber bar chart (2.2-2.4 / 2.2-2.4)

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Humber 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.

Bar, PSI and kPa

Bar-led conversions around the Oldtimer Humber. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Oldtimer Humber placard versus sidewall

The tyre-information placard on a Oldtimer Humber sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (245/40R18 and others)

Planning cold pressures for sizes often seen on a passenger car. This Humber sample opens with 245/40R18, then 215/55R16 and 225/40R18.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	38 psi / 2.62 bar

How to set the Humber

Park the Oldtimer Humber for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Humber is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Humber.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Oldtimer notes

No special Oldtimer exception: the Humber uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Oldtimer Humber usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Oldtimer sticker and this page disagree, the sticker wins.

Other Oldtimer models

Arnolt Abarth Aurora Alfa Romeo Autobianchi Auburn ASC Armstrong Siddeley

Questions about this Humber

Front versus rear on the Oldtimer Humber?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a Oldtimer Humber use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Is the sidewall number correct on a Oldtimer Humber?

No. Sidewall PSI is a maximum. The Humber placard is the operating target, near 32-35/32-35 psi.

What PSI if I plus-size toward 225/40R18?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 245/40R18, 215/55R16 and 225/40R18 as a planning band.

Handbook: placard · bar vs PSI · front vs rear · cold inflation