Oldtimer · Austin · Rear
Oldtimer Austin rear tyres: 32-35 psi / 2.2-2.4 bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi rear
34
2.31 bar · 231 kPa at the rear axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Loaded Austin rears often need the sticker’s second column, not a copy of the front 32-35 psi figure. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed Oldtimer tyre.
Oldtimer Austin placard versus sidewall
The tyre-information placard on a Oldtimer Austin sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.
Estimated pressure by tyre size (185/65R15 and others)
If your Oldtimer Austin no longer wears the OEM diameter, start at the row nearest 185/65R15 or 215/50R17 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 185/65R15 | — | 33 | — | 2.28 | — | 228 | Small / older car |
| 215/50R17 | — | 35 | — | 2.41 | — | 241 | Plus-size 17-inch |
| 225/50R17 | — | 35 | — | 2.41 | — | 241 | Touring 17-inch |
| 195/65R15 | — | 34 | — | 2.34 | — | 234 | Very common compact |
| 225/40R18 | — | 36 | — | 2.48 | — | 248 | Low-profile 18-inch |
| 245/40R18 | — | 36 | — | 2.48 | — | 248 | Wide touring 18-inch |
| 205/60R16 | — | 34 | — | 2.34 | — | 234 | Taller 16-inch |
| 205/55R16 | — | 34 | — | 2.34 | — | 234 | Typical mid-compact OEM |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
A family passenger car with a boot full of luggage should use the laden rear figure if Ford, VW or Mercedes printed one. Otherwise the modest steps in the load table are only a sketch for this Austin.
How to set the Austin
- Park the Oldtimer Austin for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Austin is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Oldtimer Austin band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Austin.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Oldtimer notes
No special Oldtimer exception: the Austin uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Oldtimer Austin usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Oldtimer sticker and this page disagree, the sticker wins.
Other Oldtimer models
Questions about this Austin
Front versus rear on the Oldtimer Austin?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What is that in bar and kPa for the Austin?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What PSI if I plus-size toward 225/50R17?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 185/65R15, 215/50R17 and 225/50R17 as a planning band.
What tyre pressure should a Oldtimer Austin use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
Handbook: placard · bar vs PSI · front vs rear · cold inflation