Mitsubishi · 3000 GT · Front
Mitsubishi 3000 GT front tyre pressure
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
The front axle of a Mitsubishi 3000 GT steers and, on front-wheel drive cars, often pulls as well. Catalogue front pressure is 32-35 psi / 2.2-2.4 bar. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Mitsubishi 3000 GT placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this 3000 GT is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (205/55R16 and others)
If your Mitsubishi 3000 GT no longer wears the OEM diameter, start at the row nearest 205/55R16 or 195/65R15 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 205/55R16 | 34 | — | 2.34 | — | 234 | — | Typical mid-compact OEM |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
| 225/40R18 | 36 | — | 2.48 | — | 248 | — | Low-profile 18-inch |
| 185/65R15 | 33 | — | 2.28 | — | 228 | — | Small / older car |
| 215/50R17 | 35 | — | 2.41 | — | 241 | — | Plus-size 17-inch |
| 205/60R16 | 34 | — | 2.34 | — | 234 | — | Taller 16-inch |
| 225/45R17 | 35 | — | 2.41 | — | 241 | — | Sport 17-inch |
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
Steering feel on the 3000 GT lives on this axle. Do not drop front pressure to “soften” a plus-size 225/40R18; you will roll the sidewall in a roundabout.
How to set the 3000 GT
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep 3000 GT numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
PSI, bar and kPa
PSI-led conversions for the Mitsubishi 3000 GT band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 3000 GT.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Mitsubishi notes
No special Mitsubishi exception: the 3000 GT uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Mitsubishi 3000 GT usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
A cheap gauge and a monthly habit will do more for this 3000 GT than nitrogen upsells.
Other Mitsubishi models
Questions about this 3000 GT
What is that in bar and kPa for the 3000 GT?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What PSI if I plus-size toward 225/40R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 205/55R16, 195/65R15 and 225/40R18 as a planning band.
Is the sidewall number correct on a Mitsubishi 3000 GT?
No. Sidewall PSI is a maximum. The 3000 GT placard is the operating target, near 32-35/32-35 psi.
How often should I check a 3000 GT?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
What tyre pressure should a Mitsubishi 3000 GT use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation