MINI · John Cooper Works Roadster · Rear
MINI John Cooper Works Roadster rear tyres: 32-35 psi / 2.2-2.4 bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi rear
34
2.31 bar · 231 kPa at the rear axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
The rear of a passenger car takes passengers, luggage and, on vans, payload. Catalogue rear pressure on the MINI John Cooper Works Roadster is 32-35 psi / 2.2-2.4 bar. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
MINI John Cooper Works Roadster placard versus sidewall
If the MINI sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Estimated pressure by tyre size (225/40R18 and others)
225/40R18 is the first planning size here. 205/60R16 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/40R18 | — | 36 | — | 2.48 | — | 248 | Low-profile 18-inch |
| 225/50R17 | — | 35 | — | 2.41 | — | 241 | Touring 17-inch |
| 205/60R16 | — | 34 | — | 2.34 | — | 234 | Taller 16-inch |
| 225/45R17 | — | 35 | — | 2.41 | — | 241 | Sport 17-inch |
| 215/55R16 | — | 35 | — | 2.41 | — | 241 | Slightly wider 16-inch |
| 245/40R18 | — | 36 | — | 2.48 | — | 248 | Wide touring 18-inch |
| 215/50R17 | — | 35 | — | 2.41 | — | 241 | Plus-size 17-inch |
| 185/65R15 | — | 33 | — | 2.28 | — | 228 | Small / older car |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
A family passenger car with a boot full of luggage should use the laden rear figure if Ford, VW or Mercedes printed one. Otherwise the modest steps in the load table are only a sketch for this John Cooper Works Roadster.
How to set the John Cooper Works Roadster
- Park the MINI John Cooper Works Roadster for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive John Cooper Works Roadster is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the MINI John Cooper Works Roadster band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this John Cooper Works Roadster.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
MINI notes
MINI run-flats ride harshly if you overshoot. Stay in the printed band on this John Cooper Works Roadster.
Spare and inflator kit
A matching full-size spare on the MINI John Cooper Works Roadster usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the MINI sticker and this page disagree, the sticker wins.
Other MINI models
Questions about this John Cooper Works Roadster
Front versus rear on the MINI John Cooper Works Roadster?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a MINI John Cooper Works Roadster use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
When does TPMS warn on a MINI John Cooper Works Roadster?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
Is the sidewall number correct on a MINI John Cooper Works Roadster?
No. Sidewall PSI is a maximum. The John Cooper Works Roadster placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 205/60R16?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/40R18, 225/50R17 and 205/60R16 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation