UK · EU reference Tyre Pressure

MINI · John Cooper Works Cabrio · PSI

MINI John Cooper Works Cabrio tyre PSI

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

PSI is the Imperial reading most UK motorists still see on garage hoses. For the MINI John Cooper Works Cabrio the catalogue row is 32-35 psi front and 32-35 psi rear. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed MINI tyre.

MINI John Cooper Works Cabrio placard versus sidewall

If the MINI sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

PSI, bar and kPa

PSI-led conversions for the MINI John Cooper Works Cabrio band (32-35 / 32-35).

PSIBarkPa
302.07207
322.21221
332.28228
33.52.31231
352.41241
362.48248
382.62262
402.76276
443.03303
503.45345
604.14414

Estimated pressure by tyre size (205/60R16 and others)

Planning cold pressures for sizes often seen on a passenger car. This John Cooper Works Cabrio sample opens with 205/60R16, then 215/50R17 and 215/55R16.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
205/60R1634342.342.34234234Taller 16-inch
215/50R1735352.412.41241241Plus-size 17-inch
215/55R1634352.342.41234241Slightly wider 16-inch
225/40R1836362.482.48248248Low-profile 18-inch
205/55R1634342.342.34234234Typical mid-compact OEM
245/40R1836362.482.48248248Wide touring 18-inch
225/45R1735352.412.41241241Sport 17-inch
195/65R1534342.342.34234234Very common compact

How to set the John Cooper Works Cabrio

  1. Measure before the school run, not after the M25.
  2. Write LF / RF / RR / RL. Do not keep John Cooper Works Cabrio numbers in your head.
  3. Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
  4. If one corner is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy34 psi / 2.34 bar35 psi / 2.41 bar
Motorway + luggage35 psi / 2.41 bar37 psi / 2.55 bar

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this John Cooper Works Cabrio.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

MINI notes

MINI run-flats ride harshly if you overshoot. Stay in the printed band on this John Cooper Works Cabrio.

Spare and inflator kit

A matching full-size spare on the MINI John Cooper Works Cabrio usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

A cheap gauge and a monthly habit will do more for this John Cooper Works Cabrio than nitrogen upsells.

Other MINI models

Questions about this John Cooper Works Cabrio

Front versus rear on the MINI John Cooper Works Cabrio?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

When does TPMS warn on a MINI John Cooper Works Cabrio?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Is the sidewall number correct on a MINI John Cooper Works Cabrio?

No. Sidewall PSI is a maximum. The John Cooper Works Cabrio placard is the operating target, near 32-35/32-35 psi.

What is that in bar and kPa for the John Cooper Works Cabrio?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

Handbook: placard · bar vs PSI · front vs rear · cold inflation