Minari · RS MK2 · Front
Minari RS MK2 front tyre pressure
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
The front axle of a Minari RS MK2 steers and, on front-wheel drive cars, often pulls as well. Catalogue front pressure is 32-35 psi / 2.2-2.4 bar. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Minari RS MK2 placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this RS MK2 is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (225/40R18 and others)
If your Minari RS MK2 no longer wears the OEM diameter, start at the row nearest 225/40R18 or 225/50R17 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/40R18 | 36 | — | 2.48 | — | 248 | — | Low-profile 18-inch |
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
| 215/50R17 | 35 | — | 2.41 | — | 241 | — | Plus-size 17-inch |
| 185/65R15 | 33 | — | 2.28 | — | 228 | — | Small / older car |
| 245/40R18 | 36 | — | 2.48 | — | 248 | — | Wide touring 18-inch |
| 215/55R16 | 34 | — | 2.34 | — | 234 | — | Slightly wider 16-inch |
| 205/55R16 | 34 | — | 2.34 | — | 234 | — | Typical mid-compact OEM |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 37 psi / 2.55 bar |
Steering feel on the RS MK2 lives on this axle. Do not drop front pressure to “soften” a plus-size 215/50R17; you will roll the sidewall in a roundabout.
How to set the RS MK2
- Park the Minari RS MK2 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive RS MK2 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Minari RS MK2 band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this RS MK2.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Minari notes
No special Minari exception: the RS MK2 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Minari RS MK2 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Minari sticker and this page disagree, the sticker wins.
Other Minari models
Questions about this RS MK2
What is that in bar and kPa for the RS MK2?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
How often should I check a RS MK2?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a Minari RS MK2?
No. Sidewall PSI is a maximum. The RS MK2 placard is the operating target, near 32-35/32-35 psi.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What tyre pressure should a Minari RS MK2 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation