Melex · 374 · PSI
Melex 374 inflation in PSI (32-35 front, 32-35 rear)
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
If a 374 owner asks “what PSI?”, start at 34 at the steering axle and 34 at the rear, then confirm the placard. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Melex 374 placard versus sidewall
The tyre-information placard on a Melex 374 sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.
PSI, bar and kPa
PSI-led conversions for the Melex 374 band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Estimated pressure by tyre size (195/65R15 and others)
If your Melex 374 no longer wears the OEM diameter, start at the row nearest 195/65R15 or 205/60R16 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
How to set the 374
- Park the Melex 374 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive 374 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 37 psi / 2.55 bar |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 374.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Melex notes
No special Melex exception: the 374 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Melex 374 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Melex sticker and this page disagree, the sticker wins.
Other Melex models
Questions about this 374
What is that in bar and kPa for the 374?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
How often should I check a 374?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a Melex 374?
No. Sidewall PSI is a maximum. The 374 placard is the operating target, near 32-35/32-35 psi.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What tyre pressure should a Melex 374 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation