Melex · 363 · Overview
Tyre pressure chart for the Melex 363
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
This front-wheel drive passenger car is filed here with a working range of 32-35/32-35 psi. The pillar sticker on your VIN still overrides the website. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed Melex tyre.
PSI, bar and kPa
1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Mid-points on the 363: 34 psi = 2.31 bar = 231 kPa.
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
How to set the 363
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep 363 numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 37 psi / 2.55 bar |
Spare and inflator kit
A matching full-size spare on the Melex 363 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
Melex notes
No special Melex exception: the 363 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Melex 363 placard versus sidewall
If the Melex sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Temperature and a cold gauge
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 363.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Estimated pressure by tyre size (225/45R17 and others)
225/45R17 is the first planning size here. 195/65R15 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
If the Melex sticker and this page disagree, the sticker wins.
Other Melex models
Questions about this 363
What is that in bar and kPa for the 363?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What tyre pressure should a Melex 363 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
How often should I check a 363?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a Melex 363?
No. Sidewall PSI is a maximum. The 363 placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 195/65R15?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 245/40R18 and 195/65R15 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation