Holden · SSX · Front
Front axle PSI and bar on the Holden SSX
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi front
34
2.31 bar · 231 kPa at the steering axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A 3 psi miss on one front corner of this SSX shows up as a wander before the TPMS lamp bothers you. Target 34 psi (2.31 bar) cold. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed Holden tyre.
Holden SSX placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this SSX is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (185/65R15 and others)
185/65R15 is the first planning size here. 225/50R17 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 185/65R15 | 33 | — | 2.28 | — | 228 | — | Small / older car |
| 215/50R17 | 35 | — | 2.41 | — | 241 | — | Plus-size 17-inch |
| 225/50R17 | 35 | — | 2.41 | — | 241 | — | Touring 17-inch |
| 205/60R16 | 34 | — | 2.34 | — | 234 | — | Taller 16-inch |
| 225/45R17 | 35 | — | 2.41 | — | 241 | — | Sport 17-inch |
| 195/65R15 | 34 | — | 2.34 | — | 234 | — | Very common compact |
| 245/40R18 | 36 | — | 2.48 | — | 248 | — | Wide touring 18-inch |
| 215/55R16 | 34 | — | 2.34 | — | 234 | — | Slightly wider 16-inch |
Pressure against load
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
Steering feel on the SSX lives on this axle. Do not drop front pressure to “soften” a plus-size 225/50R17; you will roll the sidewall in a roundabout.
How to set the SSX
- Park the Holden SSX for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive SSX is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the Holden SSX band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this SSX.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Holden notes
No special Holden exception: the SSX uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Holden SSX usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Holden sticker and this page disagree, the sticker wins.
Other Holden models
Questions about this SSX
What is that in bar and kPa for the SSX?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
When does TPMS warn on a Holden SSX?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
How often should I check a SSX?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Front versus rear on the Holden SSX?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a Holden SSX use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation