Fiat · New Panda · Bar

Recommended bar for a Fiat New Panda

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this New Panda 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Size estimates on this page include 205/60R16, 195/65R15 and 215/50R17 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the Fiat New Panda. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Fiat New Panda placard versus sidewall

If the Fiat sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (205/60R16 and others)

205/60R16 is the first planning size here. 215/50R17 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	37 psi / 2.55 bar

How to set the New Panda

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep New Panda numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this New Panda.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Fiat notes

No special Fiat exception: the New Panda uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Fiat New Panda usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Fiat sticker and this page disagree, the sticker wins.

Other Fiat models

133 2300 131 595 Abarth 242 126 128 500

Questions about this New Panda

How often should I check a New Panda?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

What PSI if I plus-size toward 215/50R17?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 205/60R16, 195/65R15 and 215/50R17 as a planning band.

Front versus rear on the Fiat New Panda?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

When does TPMS warn on a Fiat New Panda?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Is the sidewall number correct on a Fiat New Panda?

No. Sidewall PSI is a maximum. The New Panda placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation