Fiat · 126 · Bar

Fiat 126 bar chart (2.2-2.4 / 2.2-2.4)

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

European and UK handbooks usually quote bar. The Fiat 126 catalogue is 2.2-2.4 bar front and 2.2-2.4 bar rear (midpoint 2.31 / 2.31). Size estimates on this page include 195/65R15, 205/60R16 and 215/50R17 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the Fiat 126. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Fiat 126 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this 126 is the pillar sticker, near 34/34 psi.

Estimated pressure by tyre size (195/65R15 and others)

195/65R15 is the first planning size here. 215/50R17 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	37 psi / 2.55 bar

How to set the 126

Park the Fiat 126 for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive 126 is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 126.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Fiat notes

No special Fiat exception: the 126 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Fiat 126 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Fiat sticker and this page disagree, the sticker wins.

Other Fiat models

500C 242 127 132 500C Abarth 500e 600e 238

Questions about this 126

Front versus rear on the Fiat 126?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a Fiat 126 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

What is that in bar and kPa for the 126?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

What PSI if I plus-size toward 215/50R17?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 195/65R15, 205/60R16 and 215/50R17 as a planning band.

Handbook: placard · bar vs PSI · front vs rear · cold inflation