Bedford · KB · Bar
Bedford KB tyre pressure in bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
bar
2.31 / 2.31
32-35 / 32-35 psi · 231 / 231 kPa
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A front-wheel drive Bedford KB still wants even corners. 2.2-2.4 vs 2.2-2.4 is an axle split, not a left-right split. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
Bar, PSI and kPa
Bar-led conversions around the Bedford KB. 2.2-2.4 bar is not “32-35 divided by ten”.
| Bar | PSI | kPa |
|---|---|---|
| 2.07 | 30 | 207 |
| 2.21 | 32 | 221 |
| 2.28 | 33 | 228 |
| 2.31 | 33.5 | 231 |
| 2.41 | 35 | 241 |
| 2.48 | 36 | 248 |
| 2.62 | 38 | 262 |
| 2.76 | 40 | 276 |
| 3.03 | 44 | 303 |
| 3.45 | 50 | 345 |
| 4.14 | 60 | 414 |
Bedford KB placard versus sidewall
The tyre-information placard on a Bedford KB sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.
Estimated pressure by tyre size (185/65R15 and others)
Planning cold pressures for sizes often seen on a passenger car. This KB sample opens with 185/65R15, then 205/55R16 and 225/50R17.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
How to set the KB
- Park the Bedford KB for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive KB is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this KB.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
Bedford notes
No special Bedford exception: the KB uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Bedford KB usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Bedford sticker and this page disagree, the sticker wins.
Other Bedford models
Questions about this KB
Front versus rear on the Bedford KB?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a Bedford KB use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
When does TPMS warn on a Bedford KB?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
Is the sidewall number correct on a Bedford KB?
No. Sidewall PSI is a maximum. The KB placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 225/50R17?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 185/65R15, 205/55R16 and 225/50R17 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation