Bedford · CF2 · Bar

Bedford CF2 tyre pressure in bar

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

European and UK handbooks usually quote bar. The Bedford CF2 catalogue is 2.2-2.4 bar front and 2.2-2.4 bar rear (midpoint 2.31 / 2.31). Size estimates on this page include 245/40R18, 215/55R16 and 225/40R18 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the Bedford CF2. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Bedford CF2 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this CF2 is the pillar sticker, near 34/34 psi.

Estimated pressure by tyre size (245/40R18 and others)

Planning cold pressures for sizes often seen on a passenger car. This CF2 sample opens with 245/40R18, then 215/55R16 and 225/40R18.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
195/65R15	34	34	2.34	2.34	234	234	Very common compact
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	37 psi / 2.55 bar

How to set the CF2

Park the Bedford CF2 for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive CF2 is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this CF2.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Bedford notes

No special Bedford exception: the CF2 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Bedford CF2 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Bedford sticker and this page disagree, the sticker wins.

Other Bedford models

Rascal Blitz KB Astravan Midi TJ Dormobile CA

Questions about this CF2

When does TPMS warn on a Bedford CF2?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

What PSI if I plus-size toward 225/40R18?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 245/40R18, 215/55R16 and 225/40R18 as a planning band.

What tyre pressure should a Bedford CF2 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Is the sidewall number correct on a Bedford CF2?

No. Sidewall PSI is a maximum. The CF2 placard is the operating target, near 32-35/32-35 psi.

How often should I check a CF2?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Handbook: placard · bar vs PSI · front vs rear · cold inflation