UK · EU reference Tyre Pressure

245/60R18 · SUV / crossover · kPa

245/60R18 kPa inflation table

Size
245/60R18
Class
SUV / crossover
Planning PSI
36
Planning bar
2.48

kPa

248

2.48 bar · 36 psi · 100 kPa = 1 bar

245/60R18 · 36 psi · 2.48 bar · 248 kPa — estimates. Placard wins.

If the gauge only speaks kPa, 248 kPa is the sketch for this SUV / crossover size. Fine-tune to the vehicle that actually wears 245/60R18. Under-inflation cooks the shoulders of a 245/60R18; over-inflation wears the centre rib and bangs every cat’s eye.

kPa, bar and PSI

Use the table, then set a cold gauge. 248 kPa is 100 × 2.48 bar on this size.

kPaBarPSI
2212.2132
2282.2833
2342.3434
2412.4135
2482.4836
2552.5537
2622.6238
2692.6939
2762.7640
2832.8341
2902.9042
2962.9643
3033.0344
3103.1045
3173.1746
3243.2447
3313.3148

Estimated 245/60R18 pressure by load

Load moves the rear first on a SUV / crossover. If the factory placard already has a laden column, use that — not this sketch for 245/60R18.

ConditionFront (est.)Rear (est.)
Driver only / unladen36 psi / 2.48 bar / 248 kPa37 psi / 2.55 bar / 255 kPa
Typical occupancy37 psi / 2.55 bar / 255 kPa39 psi / 2.69 bar / 269 kPa
Motorway + luggage (sketch)38 psi / 2.62 bar / 262 kPa40 psi / 2.76 bar / 276 kPa

What 245/60R18 means

245/60R18 means a 245 millimetre section width, a sidewall that is 60 percent of that width, on a 18-inch rim. The R is radial construction.

Heavier CUV 18-inch. Rim diameter 18 in; section 245 mm. Estimates on this page assume a typical load index for the SUV / crossover class.

Placard versus sidewall

This website maps size searches such as “245/60R18 psi”. It does not replace the VIN label. If the two disagree, the label wins.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 36 psi as a 20 °C baseline for 245/60R18.

AmbientGaugeBarkPaNote
−5 °C (hard frost)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
0 °C34 psi2.34 bar234 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)35 psi2.41 bar241 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)36 psi2.48 bar248 kPaBaseline for this size sketch
30 °C38 psi2.62 bar262 kPaDo not bleed a hot 245/60R18
38 °C (heatwave tarmac)39 psi2.69 bar269 kPaDo not bleed a hot 245/60R18

How to set 245/60R18

  1. Park so the 245/60R18 tyres are cold (three hours, or less than about a mile).
  2. Read the door-pillar placard for that car — not the 245/60R18 sidewall maximum.
  3. If the sticker is missing, 36 psi / 2.48 bar is only a SUV / crossover planning figure for this size.
  4. Set all four with a calibrated gauge. A 3 psi miss on one corner shows up as a wander.
  5. Refit valve caps and reset TPMS if the handbook asks for a relearn.

Cars often seen on 245/60R18

These catalogue models are often seen on 245/60R18 or a close OEM neighbour. Open the vehicle chart for axle-specific PSI and bar.

Keep 245/60R18 on the printed band for that car; 36 psi is a size sketch, not a second VIN label.

Questions about 245/60R18

What is 245/60R18 in kPa?

248 kPa is the planning midpoint (100 kPa = 1 bar). 255 kPa is one PSI higher.

Is the sidewall number correct for 245/60R18?

No. Sidewall PSI or kPa is a maximum for the carcass. Operating pressure is the door-pillar placard.

What PSI should 245/60R18 tyres be?

A SUV / crossover planning figure is about 36 psi cold (2.48 bar / 248 kPa). Confirm on the vehicle placard — two cars can share 245/60R18 and not share a sticker.

What is 245/60R18 in bar?

36 psi is 2.48 bar. Add a tenth of a bar if the placard’s laden column is higher, which is common on vans that wear this size.

Is 245/60R18 the same as a plus-size swap?

Only if that is the size you fitted. Overall diameter should stay close to OEM. Pressure still follows the car, with load index at or above original.

Handbook: placard · bar vs PSI · cold inflation · all sizes