UK · EU reference Tyre Pressure

225/60R18 · SUV / crossover · kPa

225/60R18 tyre pressure in kPa

Size
225/60R18
Class
SUV / crossover
Planning PSI
34
Planning bar
2.34

kPa

234

2.34 bar · 34 psi · 100 kPa = 1 bar

225/60R18 · 34 psi · 2.34 bar · 234 kPa — estimates. Placard wins.

If the gauge only speaks kPa, 234 kPa is the sketch for this SUV / crossover size. Fine-tune to the vehicle that actually wears 225/60R18. Under-inflation cooks the shoulders of a 225/60R18; over-inflation wears the centre rib and bangs every cat’s eye.

kPa, bar and PSI

1 bar ≈ 14.5 psi; 1 psi ≈ 6.89 kPa. Planning midpoint for 225/60R18: 34 psi = 2.34 bar = 234 kPa.

kPaBarPSI
2072.0730
2142.1431
2212.2132
2282.2833
2342.3434
2412.4135
2482.4836
2552.5537
2622.6238
2692.6939
2762.7640
2832.8341
2902.9042
2962.9643
3033.0344
3103.1045
3173.1746

Estimated 225/60R18 pressure by load

Load moves the rear first on a SUV / crossover. If the factory placard already has a laden column, use that — not this sketch for 225/60R18.

ConditionFront (est.)Rear (est.)
Driver only / unladen34 psi / 2.34 bar / 234 kPa35 psi / 2.41 bar / 241 kPa
Typical occupancy35 psi / 2.41 bar / 241 kPa37 psi / 2.55 bar / 255 kPa
Motorway + luggage (sketch)36 psi / 2.48 bar / 248 kPa38 psi / 2.62 bar / 262 kPa

What 225/60R18 means

Read 225/60R18 as width / aspect R rim. Nothing in the size string is a pressure. Pressure lives on the car, not moulded as 205 or 55.

Crossover / SUV highway size. Rim diameter 18 in; section 225 mm. Estimates on this page assume a typical load index for the SUV / crossover class.

Placard versus sidewall

This website maps size searches such as “225/60R18 psi”. It does not replace the VIN label. If the two disagree, the label wins.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for 225/60R18.

AmbientGaugeBarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline for this size sketch
30 °C36 psi2.48 bar248 kPaDo not bleed a hot 225/60R18
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot 225/60R18

How to set 225/60R18

  1. Measure before the school run, not after the motorway.
  2. Write LF / RF / RR / RL. Do not keep 225/60R18 numbers in your head.
  3. Add air in short bursts toward the placard, using 34 psi only as a map.
  4. If one 225/60R18 is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

Cars often seen on 225/60R18

225/60R18 is a valid metric size in this register even if it is not on the curated OEM shortlist. Treat the 34 psi / 2.34 bar figure as a class estimate and confirm on the vehicle that actually wears it.

If the door sticker and this 225/60R18 page disagree, the sticker wins.

Questions about 225/60R18

Is 225/60R18 the same as a plus-size swap?

Only if that is the size you fitted. Overall diameter should stay close to OEM. Pressure still follows the car, with load index at or above original.

What PSI should 225/60R18 tyres be?

A SUV / crossover planning figure is about 34 psi cold (2.34 bar / 234 kPa). Confirm on the vehicle placard — two cars can share 225/60R18 and not share a sticker.

Can I run 225/60R18 at a lower pressure for comfort?

Not as a habit. A soft 225/60R18 cooks the shoulders and dulls steering. Keep load index and stay on the placard.

What is 225/60R18 in bar?

34 psi is 2.34 bar. Add a tenth of a bar if the placard’s laden column is higher, which is common on vans that wear this size.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Handbook: placard · bar vs PSI · cold inflation · all sizes