TYN-e · TX7-e · Cold
Setting cold tyres on a TYN-e TX7-e
- Drivetrain
- front-wheel drive
- Body
- SUV / crossover
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi
34 / 34
Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Cold means the TYN-e TX7-e has stood at least three hours, or covered less than about a mile. Heat from a dual carriageway run is not the number you set. Size estimates on this page include 225/60R18, 245/60R18 and 255/50R20 — interpolated from the catalogue midpoint, not a second factory sticker.
Temperature and a cold gauge
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this TX7-e.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the TX7-e
- Park the TYN-e TX7-e for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive TX7-e is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
TYN-e TX7-e placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this TX7-e is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (225/60R18 and others)
225/60R18 is the first planning size here. 255/50R20 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/60R18 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Highway CUV |
| 245/60R18 | 36 | 37 | 2.48 | 2.55 | 248 | 255 | Heavier CUV |
| 255/50R20 | 37 | 37 | 2.55 | 2.55 | 255 | 255 | 20-inch plus-size |
| 235/65R17 | 35 | 36 | 2.41 | 2.48 | 241 | 248 | Mid-size SUV |
| 235/60R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Plus-size 18-inch |
| 245/55R19 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 19-inch |
| 215/70R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Compact crossover |
| 225/65R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Very common 17-inch |
PSI, bar and kPa
PSI-led conversions for the TYN-e TX7-e band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Load notes
Load moves the rear of a SUV / crossover first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
TYN-e notes
No special TYN-e exception: the TX7-e uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the TYN-e TX7-e usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
Keep the TYN-e TX7-e on the printed band; use 225/60R18 and 255/50R20 only as a map for non-OEM wheels.
Other TYN-e models
Questions about this TX7-e
What is that in bar and kPa for the TX7-e?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Front versus rear on the TYN-e TX7-e?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
How often should I check a TX7-e?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a TYN-e TX7-e?
No. Sidewall PSI is a maximum. The TX7-e placard is the operating target, near 32-35/32-35 psi.
What tyre pressure should a TYN-e TX7-e use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation