Triumph · TR1 · kPa
Triumph TR1 kPa inflation table
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
kPa
231 / 231
2.31 / 2.31 bar · 32-35 / 32-35 psi
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
If your gauge only speaks kPa, aim near 231 / 231 for this TR1, then fine-tune to the placard. Under-inflation cooks the shoulders of a TR1; over-inflation wears the centre rib and bangs every cat’s eye.
kPa, bar and PSI
kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this TR1 sticker uses SI units.
| kPa | Bar | PSI |
|---|---|---|
| 207 | 2.07 | 30 |
| 221 | 2.21 | 32 |
| 228 | 2.28 | 33 |
| 231 | 2.31 | 33.5 |
| 241 | 2.41 | 35 |
| 248 | 2.48 | 36 |
| 262 | 2.62 | 38 |
| 276 | 2.76 | 40 |
| 303 | 3.03 | 44 |
| 345 | 3.45 | 50 |
| 414 | 4.14 | 60 |
Estimated pressure by tyre size (215/50R17 and others)
Planning cold pressures for sizes often seen on a passenger car. This TR1 sample opens with 215/50R17, then 195/65R15 and 225/40R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
Triumph TR1 placard versus sidewall
If the Triumph sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this TR1.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the TR1
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep TR1 numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 37 psi / 2.55 bar |
Triumph notes
No special Triumph exception: the TR1 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Triumph TR1 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Triumph sticker and this page disagree, the sticker wins.
Other Triumph models
Questions about this TR1
What is that in bar and kPa for the TR1?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What tyre pressure should a Triumph TR1 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
How often should I check a TR1?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a Triumph TR1?
No. Sidewall PSI is a maximum. The TR1 placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 225/40R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 215/50R17, 195/65R15 and 225/40R18 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation