Toyota · Mirai · Bar

Recommended bar for a Toyota Mirai

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Mirai 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Under-inflation cooks the shoulders of a Mirai; over-inflation wears the centre rib and bangs every cat’s eye.

Bar, PSI and kPa

Bar-led conversions around the Toyota Mirai. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Toyota Mirai placard versus sidewall

If the Toyota sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (215/55R16 and others)

215/55R16 is the first planning size here. 205/60R16 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
185/65R15	33	33	2.28	2.28	228	228	Small / older car
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	38 psi / 2.62 bar

How to set the Mirai

Park the Toyota Mirai for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Mirai is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Mirai.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Toyota notes

Toyota trucks print front and rear separately more often than cars. A roof box on a RAV4 is a load condition, not a forum “add 5 psi” rule.

Spare and inflator kit

A matching full-size spare on the Toyota Mirai usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

Keep the Toyota Mirai on the printed band; use 215/55R16 and 205/60R16 only as a map for non-OEM wheels.

Other Toyota models

Avensis Verso Aristo Caldina C-HR Avalon Chaser Belta Coaster

Questions about this Mirai

When does TPMS warn on a Toyota Mirai?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Front versus rear on the Toyota Mirai?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

What tyre pressure should a Toyota Mirai use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

What PSI if I plus-size toward 205/60R16?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 215/55R16, 195/65R15 and 205/60R16 as a planning band.

How often should I check a Mirai?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Handbook: placard · bar vs PSI · front vs rear · cold inflation