Toyota · Belta · kPa
Toyota Belta kPa inflation table
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
kPa
231 / 231
2.31 / 2.31 bar · 32-35 / 32-35 psi
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Kilopascals show up on some Asian stickers and ISO sheets. 231 kPa front and 231 kPa rear is the Toyota Belta midpoint (100 kPa = 1 bar). TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.
kPa, bar and PSI
kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this Belta sticker uses SI units.
| kPa | Bar | PSI |
|---|---|---|
| 207 | 2.07 | 30 |
| 221 | 2.21 | 32 |
| 228 | 2.28 | 33 |
| 231 | 2.31 | 33.5 |
| 241 | 2.41 | 35 |
| 248 | 2.48 | 36 |
| 262 | 2.62 | 38 |
| 276 | 2.76 | 40 |
| 303 | 3.03 | 44 |
| 345 | 3.45 | 50 |
| 414 | 4.14 | 60 |
Estimated pressure by tyre size (205/55R16 and others)
If your Toyota Belta no longer wears the OEM diameter, start at the row nearest 205/55R16 or 185/65R15 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
Toyota Belta placard versus sidewall
The tyre-information placard on a Toyota Belta sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Belta.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the Belta
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep Belta numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 38 psi / 2.62 bar |
Toyota notes
Toyota trucks print front and rear separately more often than cars. A roof box on a RAV4 is a load condition, not a forum “add 5 psi” rule.
Spare and inflator kit
A matching full-size spare on the Toyota Belta usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Toyota sticker and this page disagree, the sticker wins.
Other Toyota models
Questions about this Belta
What is that in bar and kPa for the Belta?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
When does TPMS warn on a Toyota Belta?
Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.
How often should I check a Belta?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Front versus rear on the Toyota Belta?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a Toyota Belta use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation