SEAT · Mii · Bar
SEAT Mii tyre pressure in bar
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
bar
2.31 / 2.31
32-35 / 32-35 psi · 231 / 231 kPa
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A front-wheel drive SEAT Mii still wants even corners. 2.2-2.4 vs 2.2-2.4 is an axle split, not a left-right split. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed SEAT tyre.
Bar, PSI and kPa
Bar-led conversions around the SEAT Mii. 2.2-2.4 bar is not “32-35 divided by ten”.
| Bar | PSI | kPa |
|---|---|---|
| 2.07 | 30 | 207 |
| 2.21 | 32 | 221 |
| 2.28 | 33 | 228 |
| 2.31 | 33.5 | 231 |
| 2.41 | 35 | 241 |
| 2.48 | 36 | 248 |
| 2.62 | 38 | 262 |
| 2.76 | 40 | 276 |
| 3.03 | 44 | 303 |
| 3.45 | 50 | 345 |
| 4.14 | 60 | 414 |
SEAT Mii placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Mii is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (205/60R16 and others)
Planning cold pressures for sizes often seen on a passenger car. This Mii sample opens with 205/60R16, then 195/65R15 and 225/40R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 36 psi / 2.48 bar |
How to set the Mii
- Park the SEAT Mii for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Mii is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Mii.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
SEAT notes
No special SEAT exception: the Mii uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the SEAT Mii usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the SEAT sticker and this page disagree, the sticker wins.
Other SEAT models
Questions about this Mii
What is that in bar and kPa for the Mii?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
Is the sidewall number correct on a SEAT Mii?
No. Sidewall PSI is a maximum. The Mii placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 225/40R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 205/60R16, 195/65R15 and 225/40R18 as a planning band.
What tyre pressure should a SEAT Mii use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation