Ruf · RT 12 · kPa
Ruf RT 12 tyre pressure in kPa
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
kPa
231 / 231
2.31 / 2.31 bar · 32-35 / 32-35 psi
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
If your gauge only speaks kPa, aim near 231 / 231 for this RT 12, then fine-tune to the placard. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed Ruf tyre.
kPa, bar and PSI
kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this RT 12 sticker uses SI units.
| kPa | Bar | PSI |
|---|---|---|
| 207 | 2.07 | 30 |
| 221 | 2.21 | 32 |
| 228 | 2.28 | 33 |
| 231 | 2.31 | 33.5 |
| 241 | 2.41 | 35 |
| 248 | 2.48 | 36 |
| 262 | 2.62 | 38 |
| 276 | 2.76 | 40 |
| 303 | 3.03 | 44 |
| 345 | 3.45 | 50 |
| 414 | 4.14 | 60 |
Estimated pressure by tyre size (225/45R17 and others)
Planning cold pressures for sizes often seen on a passenger car. This RT 12 sample opens with 225/45R17, then 215/55R16 and 245/40R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
Ruf RT 12 placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this RT 12 is the pillar sticker, near 34/34 psi.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this RT 12.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the RT 12
- Park the Ruf RT 12 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive RT 12 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
Ruf notes
No special Ruf exception: the RT 12 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Ruf RT 12 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Ruf sticker and this page disagree, the sticker wins.
Other Ruf models
Questions about this RT 12
Front versus rear on the Ruf RT 12?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
Is the sidewall number correct on a Ruf RT 12?
No. Sidewall PSI is a maximum. The RT 12 placard is the operating target, near 32-35/32-35 psi.
What tyre pressure should a Ruf RT 12 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What PSI if I plus-size toward 245/40R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 215/55R16 and 245/40R18 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation