UK · EU reference Tyre Pressure

Oldtimer · BMW · Bar

Oldtimer BMW tyre pressure in bar

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

A front-wheel drive Oldtimer BMW still wants even corners. 2.2-2.4 vs 2.2-2.4 is an axle split, not a left-right split. Under-inflation cooks the shoulders of a BMW; over-inflation wears the centre rib and bangs every cat’s eye.

Bar, PSI and kPa

Bar-led conversions around the Oldtimer BMW. 2.2-2.4 bar is not “32-35 divided by ten”.

BarPSIkPa
2.0730207
2.2132221
2.2833228
2.3133.5231
2.4135241
2.4836248
2.6238262
2.7640276
3.0344303
3.4550345
4.1460414

Oldtimer BMW placard versus sidewall

If the Oldtimer sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (225/45R17 and others)

If your Oldtimer BMW no longer wears the OEM diameter, start at the row nearest 225/45R17 or 215/50R17 and confirm with the tyre maker’s load table.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
225/45R1735352.412.41241241Sport 17-inch
215/50R1735352.412.41241241Plus-size 17-inch
195/65R1534342.342.34234234Very common compact
185/65R1533332.282.28228228Small / older car
205/55R1634342.342.34234234Typical mid-compact OEM
205/60R1634342.342.34234234Taller 16-inch
215/55R1634352.342.41234241Slightly wider 16-inch
245/40R1836362.482.48248248Wide touring 18-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy35 psi / 2.41 bar36 psi / 2.48 bar
Motorway + luggage36 psi / 2.48 bar36 psi / 2.48 bar

How to set the BMW

  1. Park the Oldtimer BMW for at least three hours (cold tyres).
  2. Use a calibrated gauge, not the only meter on a forecourt hose.
  3. Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
  4. Recheck all four. A 2 psi miss on a front-wheel drive BMW is enough to feel a pull.
  5. Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this BMW.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

Oldtimer notes

No special Oldtimer exception: the BMW uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Oldtimer BMW usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Oldtimer sticker and this page disagree, the sticker wins.

Other Oldtimer models

Questions about this BMW

How often should I check a BMW?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

When does TPMS warn on a Oldtimer BMW?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

What PSI if I plus-size toward 195/65R15?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 215/50R17 and 195/65R15 as a planning band.

Front versus rear on the Oldtimer BMW?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Is the sidewall number correct on a Oldtimer BMW?

No. Sidewall PSI is a maximum. The BMW placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation