MPM Motors · PS160 · Bar

MPM Motors PS160 tyre pressure in bar

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this PS160 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed MPM Motors tyre.

Bar, PSI and kPa

Bar-led conversions around the MPM Motors PS160. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

MPM Motors PS160 placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this PS160 is the pillar sticker, near 34/34 psi.

Estimated pressure by tyre size (205/60R16 and others)

If your MPM Motors PS160 no longer wears the OEM diameter, start at the row nearest 205/60R16 or 195/65R15 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
245/40R18	36	36	2.48	2.48	248	248	Wide touring 18-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
185/65R15	33	33	2.28	2.28	228	228	Small / older car
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	36 psi / 2.48 bar

How to set the PS160

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep PS160 numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this PS160.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

MPM Motors notes

No special MPM Motors exception: the PS160 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the MPM Motors PS160 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the MPM Motors sticker and this page disagree, the sticker wins.

Other MPM Motors models

Erelis

Questions about this PS160

Front versus rear on the MPM Motors PS160?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

When does TPMS warn on a MPM Motors PS160?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a MPM Motors PS160 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Is the sidewall number correct on a MPM Motors PS160?

No. Sidewall PSI is a maximum. The PS160 placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation