Melex · 466 · kPa
Melex 466 kPa inflation table
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
kPa
231 / 231
2.31 / 2.31 bar · 32-35 / 32-35 psi
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Kilopascals show up on some Asian stickers and ISO sheets. 231 kPa front and 231 kPa rear is the Melex 466 midpoint (100 kPa = 1 bar). Size estimates on this page include 245/40R18, 215/55R16 and 195/65R15 — interpolated from the catalogue midpoint, not a second factory sticker.
kPa, bar and PSI
kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this 466 sticker uses SI units.
| kPa | Bar | PSI |
|---|---|---|
| 207 | 2.07 | 30 |
| 221 | 2.21 | 32 |
| 228 | 2.28 | 33 |
| 231 | 2.31 | 33.5 |
| 241 | 2.41 | 35 |
| 248 | 2.48 | 36 |
| 262 | 2.62 | 38 |
| 276 | 2.76 | 40 |
| 303 | 3.03 | 44 |
| 345 | 3.45 | 50 |
| 414 | 4.14 | 60 |
Estimated pressure by tyre size (245/40R18 and others)
If your Melex 466 no longer wears the OEM diameter, start at the row nearest 245/40R18 or 215/55R16 and confirm with the tyre maker’s load table.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 215/55R16 | 34 | 35 | 2.34 | 2.41 | 234 | 241 | Slightly wider 16-inch |
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
Melex 466 placard versus sidewall
If the Melex sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 466.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the 466
- Park the Melex 466 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive 466 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 37 psi / 2.55 bar |
Melex notes
No special Melex exception: the 466 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Melex 466 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Melex sticker and this page disagree, the sticker wins.
Other Melex models
Questions about this 466
What is that in bar and kPa for the 466?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What PSI if I plus-size toward 195/65R15?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 245/40R18, 215/55R16 and 195/65R15 as a planning band.
Is the sidewall number correct on a Melex 466?
No. Sidewall PSI is a maximum. The 466 placard is the operating target, near 32-35/32-35 psi.
Front versus rear on the Melex 466?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
What tyre pressure should a Melex 466 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Handbook: placard · bar vs PSI · front vs rear · cold inflation