Mazda · Capella · PSI

What PSI for a Mazda Capella?

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

If a Capella owner asks “what PSI?”, start at 34 at the steering axle and 34 at the rear, then confirm the placard. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.

Mazda Capella placard versus sidewall

Sidewall PSI is a carcass maximum. Recommended operating pressure for this Capella is the pillar sticker, near 34/34 psi.

PSI, bar and kPa

PSI-led conversions for the Mazda Capella band (32-35 / 32-35).

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

Estimated pressure by tyre size (225/45R17 and others)

225/45R17 is the first planning size here. 205/60R16 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch

How to set the Capella

Park the Mazda Capella for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Capella is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	36 psi / 2.48 bar

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Capella.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Mazda notes

No special Mazda exception: the Capella uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Mazda Capella usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Mazda sticker and this page disagree, the sticker wins.

Other Mazda models

CX-5 CX-3 929 CX-6e 6 CX-60 626 5

Questions about this Capella

What is that in bar and kPa for the Capella?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

Is the sidewall number correct on a Mazda Capella?

No. Sidewall PSI is a maximum. The Capella placard is the operating target, near 32-35/32-35 psi.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a Mazda Capella use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

What PSI if I plus-size toward 205/60R16?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 185/65R15 and 205/60R16 as a planning band.

Handbook: placard · bar vs PSI · front vs rear · cold inflation