UK · EU reference Tyre Pressure

Lifan · Foison · kPa

Lifan Foison kPa inflation table

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

kPa

231 / 231

2.31 / 2.31 bar · 32-35 / 32-35 psi

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

Kilopascals show up on some Asian stickers and ISO sheets. 231 kPa front and 231 kPa rear is the Lifan Foison midpoint (100 kPa = 1 bar). TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.

kPa, bar and PSI

kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this Foison sticker uses SI units.

kPaBarPSI
2072.0730
2212.2132
2282.2833
2312.3133.5
2412.4135
2482.4836
2622.6238
2762.7640
3033.0344
3453.4550
4144.1460

Estimated pressure by tyre size (225/45R17 and others)

If your Lifan Foison no longer wears the OEM diameter, start at the row nearest 225/45R17 or 185/65R15 and confirm with the tyre maker’s load table.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
225/45R1735352.412.41241241Sport 17-inch
185/65R1533332.282.28228228Small / older car
205/55R1634342.342.34234234Typical mid-compact OEM
215/55R1634352.342.41234241Slightly wider 16-inch
195/65R1534342.342.34234234Very common compact
245/40R1836362.482.48248248Wide touring 18-inch
215/50R1735352.412.41241241Plus-size 17-inch
225/50R1735352.412.41241241Touring 17-inch

Lifan Foison placard versus sidewall

The tyre-information placard on a Lifan Foison sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Foison.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

How to set the Foison

  1. Measure before the school run, not after the M25.
  2. Write LF / RF / RR / RL. Do not keep Foison numbers in your head.
  3. Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
  4. If one corner is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy34 psi / 2.34 bar35 psi / 2.41 bar
Motorway + luggage35 psi / 2.41 bar38 psi / 2.62 bar

Lifan notes

No special Lifan exception: the Foison uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Lifan Foison usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Lifan sticker and this page disagree, the sticker wins.

Other Lifan models

Questions about this Foison

What is that in bar and kPa for the Foison?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

When does TPMS warn on a Lifan Foison?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Front versus rear on the Lifan Foison?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What tyre pressure should a Lifan Foison use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation