Li · L6 · Bar

Li L6 bar chart (2.2-2.4 / 2.2-2.4)

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this L6 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Size estimates on this page include 225/45R17, 225/40R18 and 195/65R15 — interpolated from the catalogue midpoint, not a second factory sticker.

Bar, PSI and kPa

Bar-led conversions around the Li L6. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Li L6 placard versus sidewall

The tyre-information placard on a Li L6 sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (225/45R17 and others)

225/45R17 is the first planning size here. 195/65R15 is usually the plus-size or LT step. Keep load index at or above original equipment.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
225/50R17	35	35	2.41	2.41	241	241	Touring 17-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	38 psi / 2.62 bar

How to set the L6

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep L6 numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this L6.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Li notes

No special Li exception: the L6 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Li L6 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Li sticker and this page disagree, the sticker wins.

Other Li models

L7 L8 L9

Questions about this L6

What is that in bar and kPa for the L6?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

When does TPMS warn on a Li L6?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Is the sidewall number correct on a Li L6?

No. Sidewall PSI is a maximum. The L6 placard is the operating target, near 32-35/32-35 psi.

What PSI if I plus-size toward 195/65R15?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/45R17, 225/40R18 and 195/65R15 as a planning band.

What tyre pressure should a Li L6 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation