UK · EU reference Tyre Pressure

Kia · Leo · Bar

Kia Leo tyre pressure in bar

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Leo 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Under-inflation cooks the shoulders of a Leo; over-inflation wears the centre rib and bangs every cat’s eye.

Bar, PSI and kPa

Bar-led conversions around the Kia Leo. 2.2-2.4 bar is not “32-35 divided by ten”.

BarPSIkPa
2.0730207
2.2132221
2.2833228
2.3133.5231
2.4135241
2.4836248
2.6238262
2.7640276
3.0344303
3.4550345
4.1460414

Kia Leo placard versus sidewall

If the Kia sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (195/65R15 and others)

If your Kia Leo no longer wears the OEM diameter, start at the row nearest 195/65R15 or 185/65R15 and confirm with the tyre maker’s load table.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
195/65R1534342.342.34234234Very common compact
185/65R1533332.282.28228228Small / older car
215/55R1634352.342.41234241Slightly wider 16-inch
225/50R1735352.412.41241241Touring 17-inch
225/45R1735352.412.41241241Sport 17-inch
205/60R1634342.342.34234234Taller 16-inch
205/55R1634342.342.34234234Typical mid-compact OEM
215/50R1735352.412.41241241Plus-size 17-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy34 psi / 2.34 bar35 psi / 2.41 bar
Motorway + luggage35 psi / 2.41 bar36 psi / 2.48 bar

How to set the Leo

  1. Park the Kia Leo for at least three hours (cold tyres).
  2. Use a calibrated gauge, not the only meter on a forecourt hose.
  3. Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
  4. Recheck all four. A 2 psi miss on a front-wheel drive Leo is enough to feel a pull.
  5. Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Leo.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

Kia notes

Kia crossovers sometimes list a higher rear. Read both columns on the Leo pillar.

Spare and inflator kit

A matching full-size spare on the Kia Leo usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Kia sticker and this page disagree, the sticker wins.

Other Kia models

Questions about this Leo

Is the sidewall number correct on a Kia Leo?

No. Sidewall PSI is a maximum. The Leo placard is the operating target, near 32-35/32-35 psi.

When does TPMS warn on a Kia Leo?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

How often should I check a Leo?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Front versus rear on the Kia Leo?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

Handbook: placard · bar vs PSI · front vs rear · cold inflation