Honda · Fit · Bar

Honda Fit bar chart (2.2-2.4 / 2.2-2.4)

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this Fit 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Under-inflation cooks the shoulders of a Fit; over-inflation wears the centre rib and bangs every cat’s eye.

Bar, PSI and kPa

Bar-led conversions around the Honda Fit. 2.2-2.4 bar is not “32-35 divided by ten”.

Bar	PSI	kPa
2.07	30	207
2.21	32	221
2.28	33	228
2.31	33.5	231
2.41	35	241
2.48	36	248
2.62	38	262
2.76	40	276
3.03	44	303
3.45	50	345
4.14	60	414

Honda Fit placard versus sidewall

The tyre-information placard on a Honda Fit sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (225/40R18 and others)

If your Honda Fit no longer wears the OEM diameter, start at the row nearest 225/40R18 or 205/60R16 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
195/65R15	34	34	2.34	2.34	234	234	Very common compact
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	35 psi / 2.41 bar	36 psi / 2.48 bar
Motorway + luggage	36 psi / 2.48 bar	37 psi / 2.55 bar

How to set the Fit

Park the Honda Fit for at least three hours (cold tyres).
Use a calibrated gauge, not the only meter on a forecourt hose.
Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
Recheck all four. A 2 psi miss on a front-wheel drive Fit is enough to feel a pull.
Refit valve caps and reset TPMS if the handbook asks for a relearn.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Fit.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

Honda notes

Honda cars cluster around 32–35 psi (2.2–2.4 bar). Reset the TPMS from the cluster after a large fill on many 2008+ models.

Spare and inflator kit

A matching full-size spare on the Honda Fit usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Honda sticker and this page disagree, the sticker wins.

Other Honda models

Element Beat Inspire Capa HR-V e CR-Z Integra

Questions about this Fit

What is that in bar and kPa for the Fit?

Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.

Front versus rear on the Honda Fit?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

How often should I check a Fit?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

What PSI if I plus-size toward 185/65R15?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/40R18, 205/60R16 and 185/65R15 as a planning band.

What tyre pressure should a Honda Fit use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Handbook: placard · bar vs PSI · front vs rear · cold inflation