UK · EU reference Tyre Pressure

Ford · RS 200 · Bar

Ford RS 200 tyre pressure in bar

Drivetrain
front-wheel drive
Body
passenger car
PSI F / R
32-35 / 32-35
Bar F / R
2.2-2.4 / 2.2-2.4

bar

2.31 / 2.31

32-35 / 32-35 psi · 231 / 231 kPa

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

2.3 bar is not 23 psi. On this RS 200 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.

Bar, PSI and kPa

Bar-led conversions around the Ford RS 200. 2.2-2.4 bar is not “32-35 divided by ten”.

BarPSIkPa
2.0730207
2.2132221
2.2833228
2.3133.5231
2.4135241
2.4836248
2.6238262
2.7640276
3.0344303
3.4550345
4.1460414

Ford RS 200 placard versus sidewall

If the Ford sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.

Estimated pressure by tyre size (225/40R18 and others)

If your Ford RS 200 no longer wears the OEM diameter, start at the row nearest 225/40R18 or 245/40R18 and confirm with the tyre maker’s load table.

Tyre sizeFront PSIRear PSIFront barRear barFront kPaRear kPaNote
225/40R1836362.482.48248248Low-profile 18-inch
245/40R1836362.482.48248248Wide touring 18-inch
185/65R1533332.282.28228228Small / older car
215/50R1735352.412.41241241Plus-size 17-inch
205/55R1634342.342.34234234Typical mid-compact OEM
215/55R1634352.342.41234241Slightly wider 16-inch
225/45R1735352.412.41241241Sport 17-inch
205/60R1634342.342.34234234Taller 16-inch

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

ConditionFront (est.)Rear (est.)
Driver only34 psi / 2.34 bar34 psi / 2.34 bar
Full occupancy34 psi / 2.34 bar35 psi / 2.41 bar
Motorway + luggage35 psi / 2.41 bar36 psi / 2.48 bar

How to set the RS 200

  1. Measure before the school run, not after the M25.
  2. Write LF / RF / RR / RL. Do not keep RS 200 numbers in your head.
  3. Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
  4. If one corner is 4 psi down, hunt for a nail before you blame the weather.
  5. Log date, ambient temperature and the four readings.

Temperature drift

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this RS 200.

AmbientGauge (front mid)BarkPaNote
−5 °C (hard frost)31 psi2.14 bar214 kPaGauge reads low; do not overfill once warm
0 °C32 psi2.21 bar221 kPaGauge reads low; do not overfill once warm
8 °C (UK winter morning)33 psi2.28 bar228 kPaGauge reads low; do not overfill once warm
20 °C (set cold here)34 psi2.34 bar234 kPaBaseline
30 °C36 psi2.48 bar248 kPaDo not bleed a hot tyre
38 °C (heatwave tarmac)37 psi2.55 bar255 kPaDo not bleed a hot tyre

Ford notes

Ford UK placards on the RS 200 are often printed in PSI even when the handbook also shows bar. A Mondeo, Focus or Kuga does not share a Transit number. Loaded vans use the second column.

Spare and inflator kit

A matching full-size spare on the Ford RS 200 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

Keep the Ford RS 200 on the printed band; use 225/40R18 and 185/65R15 only as a map for non-OEM wheels.

Other Ford models

Questions about this RS 200

What tyre pressure should a Ford RS 200 use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

What PSI if I plus-size toward 185/65R15?

Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/40R18, 245/40R18 and 185/65R15 as a planning band.

How often should I check a RS 200?

Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.

Is the sidewall number correct on a Ford RS 200?

No. Sidewall PSI is a maximum. The RS 200 placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation