Fiat · Albea · kPa
Fiat Albea tyre pressure in kPa
- Drivetrain
- front-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
kPa
231 / 231
2.31 / 2.31 bar · 32-35 / 32-35 psi
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
If your gauge only speaks kPa, aim near 231 / 231 for this Albea, then fine-tune to the placard. Under-inflation cooks the shoulders of a Albea; over-inflation wears the centre rib and bangs every cat’s eye.
kPa, bar and PSI
kPa-led conversions. 220 kPa is 2.2 bar and about 32 psi — handy if this Albea sticker uses SI units.
| kPa | Bar | PSI |
|---|---|---|
| 207 | 2.07 | 30 |
| 221 | 2.21 | 32 |
| 228 | 2.28 | 33 |
| 231 | 2.31 | 33.5 |
| 241 | 2.41 | 35 |
| 248 | 2.48 | 36 |
| 262 | 2.62 | 38 |
| 276 | 2.76 | 40 |
| 303 | 3.03 | 44 |
| 345 | 3.45 | 50 |
| 414 | 4.14 | 60 |
Estimated pressure by tyre size (225/40R18 and others)
Planning cold pressures for sizes often seen on a passenger car. This Albea sample opens with 225/40R18, then 225/50R17 and 205/60R16.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
| 215/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Plus-size 17-inch |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
Fiat Albea placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Albea is the pillar sticker, near 34/34 psi.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Albea.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
How to set the Albea
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep Albea numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 37 psi / 2.55 bar |
Fiat notes
No special Fiat exception: the Albea uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the Fiat Albea usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the Fiat sticker and this page disagree, the sticker wins.
Other Fiat models
Questions about this Albea
Front versus rear on the Fiat Albea?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What tyre pressure should a Fiat Albea use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Is the sidewall number correct on a Fiat Albea?
No. Sidewall PSI is a maximum. The Albea placard is the operating target, near 32-35/32-35 psi.
What PSI if I plus-size toward 205/60R16?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 225/40R18, 225/50R17 and 205/60R16 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation