Carver · Base · Cold

Carver Base cold-inflation guide

Drivetrain: front-wheel drive
Body: passenger car
PSI F / R: 32-35 / 32-35
Bar F / R: 2.2-2.4 / 2.2-2.4

psi

34 / 34

Catalogue mid-points, front / rear · 2.2-2.4 / 2.2-2.4 bar

32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa

Cold means the Carver Base has stood at least three hours, or covered less than about a mile. Heat from a dual carriageway run is not the number you set. TPMS typically warns near 25 psi (about 25% below target). That is already a soft tyre, not a fill target.

Temperature and a cold gauge

Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Base.

Ambient	Gauge (front mid)	Bar	kPa	Note
−5 °C (hard frost)	31 psi	2.14 bar	214 kPa	Gauge reads low; do not overfill once warm
0 °C	32 psi	2.21 bar	221 kPa	Gauge reads low; do not overfill once warm
8 °C (UK winter morning)	33 psi	2.28 bar	228 kPa	Gauge reads low; do not overfill once warm
20 °C (set cold here)	34 psi	2.34 bar	234 kPa	Baseline
30 °C	36 psi	2.48 bar	248 kPa	Do not bleed a hot tyre
38 °C (heatwave tarmac)	37 psi	2.55 bar	255 kPa	Do not bleed a hot tyre

How to set the Base

Measure before the school run, not after the M25.
Write LF / RF / RR / RL. Do not keep Base numbers in your head.
Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
If one corner is 4 psi down, hunt for a nail before you blame the weather.
Log date, ambient temperature and the four readings.

Carver Base placard versus sidewall

The tyre-information placard on a Carver Base sits on the driver’s door pillar (sometimes the fuel-filler flap). Catalogue figures here are a general band: 32-35 / 32-35 psi.

Estimated pressure by tyre size (215/55R16 and others)

If your Carver Base no longer wears the OEM diameter, start at the row nearest 215/55R16 or 225/45R17 and confirm with the tyre maker’s load table.

Tyre size	Front PSI	Rear PSI	Front bar	Rear bar	Front kPa	Rear kPa	Note
215/55R16	34	35	2.34	2.41	234	241	Slightly wider 16-inch
225/45R17	35	35	2.41	2.41	241	241	Sport 17-inch
205/60R16	34	34	2.34	2.34	234	234	Taller 16-inch
185/65R15	33	33	2.28	2.28	228	228	Small / older car
195/65R15	34	34	2.34	2.34	234	234	Very common compact
215/50R17	35	35	2.41	2.41	241	241	Plus-size 17-inch
205/55R16	34	34	2.34	2.34	234	234	Typical mid-compact OEM
225/40R18	36	36	2.48	2.48	248	248	Low-profile 18-inch

PSI, bar and kPa

PSI-led conversions for the Carver Base band (32-35 / 32-35).

PSI	Bar	kPa
30	2.07	207
32	2.21	221
33	2.28	228
33.5	2.31	231
35	2.41	241
36	2.48	248
38	2.62	262
40	2.76	276
44	3.03	303
50	3.45	345
60	4.14	414

Load notes

Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.

Condition	Front (est.)	Rear (est.)
Driver only	34 psi / 2.34 bar	34 psi / 2.34 bar
Full occupancy	34 psi / 2.34 bar	35 psi / 2.41 bar
Motorway + luggage	35 psi / 2.41 bar	36 psi / 2.48 bar

Carver notes

No special Carver exception: the Base uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.

Spare and inflator kit

A matching full-size spare on the Carver Base usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.

If the Carver sticker and this page disagree, the sticker wins.

Other Carver models

Cargo

Questions about this Base

Front versus rear on the Carver Base?

This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.

What tyre pressure should a Carver Base use?

Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.

When does TPMS warn on a Carver Base?

Direct TPMS typically flags about 25% below placard — near 25 psi on this row. Fill to the sticker, not to the lamp.

Should I bleed pressure after a motorway run?

No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.

Is the sidewall number correct on a Carver Base?

No. Sidewall PSI is a maximum. The Base placard is the operating target, near 32-35/32-35 psi.

Handbook: placard · bar vs PSI · front vs rear · cold inflation