BMW · iX1 · Bar
BMW iX1 bar chart (2.2-2.4 / 2.2-2.4)
- Drivetrain
- all-wheel drive
- Body
- SUV / crossover
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
bar
2.31 / 2.31
32-35 / 32-35 psi · 231 / 231 kPa
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
A all-wheel drive BMW iX1 still wants even corners. 2.2-2.4 vs 2.2-2.4 is an axle split, not a left-right split. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed BMW tyre. Keep side-to-side spread inside about 2 psi so the all-wheel drive hardware is not working on a radius mismatch.
Bar, PSI and kPa
Bar-led conversions around the BMW iX1. 2.2-2.4 bar is not “32-35 divided by ten”.
| Bar | PSI | kPa |
|---|---|---|
| 2.07 | 30 | 207 |
| 2.21 | 32 | 221 |
| 2.28 | 33 | 228 |
| 2.31 | 33.5 | 231 |
| 2.41 | 35 | 241 |
| 2.48 | 36 | 248 |
| 2.62 | 38 | 262 |
| 2.76 | 40 | 276 |
| 3.03 | 44 | 303 |
| 3.45 | 50 | 345 |
| 4.14 | 60 | 414 |
BMW iX1 placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this iX1 is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (245/55R19 and others)
Planning cold pressures for sizes often seen on a SUV / crossover. This iX1 sample opens with 245/55R19, then 225/65R17 and 225/60R18.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 245/55R19 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 19-inch |
| 225/65R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Very common 17-inch |
| 225/60R18 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Highway CUV |
| 215/70R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Compact crossover |
| 235/65R17 | 35 | 36 | 2.41 | 2.48 | 241 | 248 | Mid-size SUV |
| 255/50R20 | 37 | 37 | 2.55 | 2.55 | 255 | 255 | 20-inch plus-size |
| 235/60R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Plus-size 18-inch |
| 245/60R18 | 36 | 37 | 2.48 | 2.55 | 248 | 255 | Heavier CUV |
Load notes
Load moves the rear of a SUV / crossover first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 37 psi / 2.55 bar |
How to set the iX1
- Measure before the school run, not after the M25.
- Write LF / RF / RR / RL. Do not keep iX1 numbers in your head.
- Add air in short bursts toward 34 psi (2.31 bar) front and 34 psi rear.
- If one corner is 4 psi down, hunt for a nail before you blame the weather.
- Log date, ambient temperature and the four readings.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this iX1.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
BMW notes
BMW run-flats still want the placard. Comfort settings in the iDrive do not replace the door-pillar figure on this iX1.
Spare and inflator kit
A matching full-size spare on the BMW iX1 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the BMW sticker and this page disagree, the sticker wins.
Other BMW models
Questions about this iX1
What is that in bar and kPa for the iX1?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
How often should I check a iX1?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
What tyre pressure should a BMW iX1 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Is the sidewall number correct on a BMW iX1?
No. Sidewall PSI is a maximum. The iX1 placard is the operating target, near 32-35/32-35 psi.
Handbook: placard · bar vs PSI · front vs rear · cold inflation